How To Change Oil And Air Filter On Craftsman Ys4500 Manual
SERVICE REMINDER/60 minutes METER
Service reminder shows the total number
of hours the engine has run and flashes to
signal that the engine or mower needs
servicing. When service is required, the
service reminder wilt flash for two hours.
To service engine and mower, see the
Maintenance section of this manual.
Notation: Service reminder runs when the igni-
tion key is in any position but "Stop". For
accurate reading, be sure primal remains inthe
"Cease" position when engine is not running.
BEFORE STARTING THE ENGINE
CHECK ENGINE OiL LEVEL
The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.
1. Check engine oil with tractor on level
footing.
2. Unthread and remove oil fill cap/dip-
stick; wipe oil off. Reinsert the dipstick
into the tube and rest oil make full cap on the
tube. Practise not thread the cap onto the
tube. Remove and read oil level. If
necessary, add oil until "FULL' marking
on dipstick is reached. Practice not overfill.
• For common cold weather condition operation you lot should
modify oil for easier starting (Meet the
oil viscosity nautical chart in the Maintenance
section of this transmission).
• To change engine oil, run across the Mainte-
nance section in this transmission.
Add GASOLINE
• Fill fuel tank to bottom of filler neck. Practise not
overfill. Usefresh, clean, regutarunleaded
gasoline with a minimum of 87 octane.
(Apply of leaded gasoline volition increase
carbon and leadoxide deposits and reduce
valve life). Do not mix oil with gasoline.
Purchase fuel inquantities that can be used
within 30 days to assure fuel freshness.
_,CAUTION: Wipe off whatsoever spilled oil or
fuel. Do not shop, spill or utilise gasoline
near an open flame.
iMPORTANT: When operating in atmosphere-
atures betow32°F(0°C), apply fresh, clean
winter grade gasoline to help insure expert
common cold conditions starting.
CAUTION: Booze blended fuels (chosen
gasohol or using ethanol or methanol) tin
attract moisture which leads to separation
and formation of acids during storage.
Acidic gas tin can damage the fuel system
of an engine while in storage. To avoid
engine issues, the fuel system should
be emptied before storage of xxx days
or longer. Bleed the gas tank, kickoff the
engine and permit it run until the fuel lines
and carburetor are empty. Use fresh fuel
side by side flavor. See Storage instructions for
additional information. Never use engine
or carburetor cleaner products inthe fuel
tank or permanent damage may occur.
TO First ENGINE
When starting the engine for the outset time
or if the engine has run out of fuel, it will
have actress cranking time to motility fuel from
the tank to the engine.
ane. Be certain freewheel control isin the
transmission engaged position.
2. Sit on seat inoperating position, depress
restriction pedal and prepare parking brake.
3. Move attachment clutch to disengaged
position.
4. Motion throttle command to fast position
five. Pullchokecontrotoutforacotd enginestart
attempt. For awarm engine starting time endeavour
the choke control may not exist needed.
Notation: Before starting, read the warm and
cold starting procedures below.
half dozen. insert fundamental into ignition and plow central
clockwise to start position and release
key equally soon as engine starts. Do not run
starter continuously for more than fifteen
seconds per minute. If the engine does
not start after several attempts, button
choke control in, wait a few minutes
and try once again. If engine notwithstanding does not
showtime, putt the choke control out and retry.
WARM Weather STARTING (l° F and
higher up)
7. When engine starts, slowly push choke
control in until the engine begins to
run smoothly, if the engine starts to
run roughly, pull the choke control out
slightly for a few seconds and and so
proceed to push button the control in slowly.
• The attachments and ground drive tin
now be used. if the engine does not
accept the load, restart the engine and
allow itto warm up for 1 minute using
the choke as described to a higher place.
COLD WEATHER STARTING (50° F and
beneath)
8. When engine starts, slowly push choke
control in until the engine begins to run
smoothly. Continue to push button the choke
control in small steps allowing the en-
gine to accept small-scale changes in speed
and load, until the choke control isfully
in. If the engine starts to run roughly,
pull the choke command out slightly for a
few seconds and and so go along to push
the control in slowly. This may require
an engine warm-up period from several
seconds to several minutes, depending
17 on the temperature.
Source: http://lawnandgarden.manualsonline.com/manuals/mfg/craftsman/yt_4500.html?p=17
Posted by: carleparld1998.blogspot.com
0 Response to "How To Change Oil And Air Filter On Craftsman Ys4500 Manual"
Post a Comment